MODELING AND SIMULATION OF NONLINEAR JOINT BEHAVIOR IN INDUSTRIAL ASSEMBLIES USING HARMONIC BALANCE METHOD AND FINITE ELEMENT ANALYSIS

Authors

  • Taha Hussein Karam Alsayyad Dept. Scholar buildings, Directorate of education in Najaf, Ministry of education, Najaf- Iraq

DOI:

https://doi.org/10.30572/2018/KJE/1704010

Keywords:

Nonlinear Joint Dynamics, Harmonic Balance Method, Craig-Bampton Sub structuring, Friction Damping, Industrial Vibration Analysis

Abstract

This paper proposes a computationally efficient framework for the simulation of nonlinear joint dynamics in complex industrial assemblies where friction-induced micro-motions have significant influences on system behavior. The proposed method combines FEA, Craig-Bampton sub-structuring, and the Jenkins friction model within an HBM solver enhanced by an AFT scheme. Sub-structuring was used to reduce the full FE model of the "Harmony" assembly from 1.2 million DOFs to 2,150 (a reduction of 99.8%) and succeeded in isolating the joint nonlinearities. The solution for nonlinear responses was obtained by HBM, while the path-following continuation method was employed to trace the amplitude-dependent behaviors. Results demonstrate excellent agreement with experiment: the model successfully predicted both a 15 Hz softening shift in the fundamental bending resonance for 50 N excitation, and approximated hysteresis loop areas within 4.9%; bifurcation and higher-harmonic generation were also captured. Most significantly, the simulation time was reduced from 72 hr in the full model to 2.1 hr in the ROM, affirming the applicability of the framework to fast, high-fidelity analysis of nonlinear industrial systems

Downloads

Download data is not yet available.

References

Arcaro, A. Zhuang, B. Gencturk, B. and Ghanem, R. (2024) 'Damage detection and localization in sealed spent nuclear fuel dry storage canisters using multi-task machine learning classifiers', reliability Engineering & System Safety, 252, 110446.

Bathe, K.J. (1996) 'Finite element procedures'.

Birk, C. Kipfmüller, M. and Kotschenreuther, J. (2025). 'Dynamic Modeling and Analysis of Industrial Robots for Enhanced Manufacturing Precision', Actuators, 14(7), pp. 311. https://doi.org/10.3390/act14070311

Brake, M.R. (2016) 'The mechanics of jointed structures, cham: Springer'.

Cameron, T. M. and Griffin, J. H. (1989) 'An Alternating Frequency/Time Domain Method for Calculating the Steady-State Response of Nonlinear Dynamic Systems', ASME. J. Appl. Mech, 56(1), pp. 149–154. https://doi.org/10.1115/1.3176036

Carlberg, K. Tuminaro, R. and Boggs, P. (2012) 'Efficient structure-preserving model reduction for nonlinear mechanical systems with application to structural dynamics and in 53rd AIAA/ASME/ASCE/AHS/ASC Structures', Structural Dynamics and Materials Conference 20th AIAA/ASME/AHS Adaptive Structures Conference 14th AIAA, pp. 1969.

Craig Jr, R.R. and Bampton, M.C. (1968) 'Coupling of substructures for dynamic analyses', AIAA journal, 6(7), pp. 1313-1319.

Dalela, S. Balaji, P.S. Leblouba, M. et al. (2024) 'Nonlinear static and dynamic response of a metastructure exhibiting quasi-zero-stiffness characteristics for vibration control: an experimental validation', Scientific Reports, 14, 19195. https://doi.org/10.1038/s41598-024-70126-x

Ferhatoglu, E. Botto, D. and Zucca, S. (2024) 'Parametric study for model calibration of a friction-damped turbine blade with multiple test data', Nonlinear Dynamics 112, pp. 7847–7873. https://doi.org/10.1007/s11071-024-09396-z

Friswell, M.I. (2007) 'Damage identification using inverse methods. Philosophical Transactions of the Royal Society A: Mathematical', Physical and Engineering Sciences, 365(1851), pp. 393-410.

Gao, Q. Fan, Y. Wu, Y. and Li, L. (2023) 'A harmonic balance-based method to predict nonlinear forced response and temperature rise of dry friction systems including frictional heat transfer', Nonlinear Dynamics, 111(15), pp. 14263-14291.

Iwan, W. D. (1966). 'A Distributed-Element Model for Hysteresis and Its Steady-State Dynamic Response', ASME. J. Appl. Mech. 33(4), pp. 893–900. https://doi.org/10.1115/1.3625199

Krack, M. (2025). 'Systems with Contact Nonlinearities', In: Touzé, C., Frangi, A. (eds) Model Order Reduction for Design, Analysis and Control of Nonlinear Vibratory Systems. CISM International Centre for Mechanical Sciences, vol 614. Springer, Cham. pp. 237-275. https://doi.org/10.1007/978-3-031-67499-0_5

Li, T. Yang, D. Zhao, B. Sun, Q. Huo, J. and Sun, W. (2021) 'Measured and investigated nonlinear dynamics parameters on bolted flange joints of the combined rotor’, Journal of Mechanical Science and Technology, 35, pp. 1841-1850.

Liu, F. Jin, D. Li, X. et al. (2024) 'Reduced-order modeling and solution method for nonlinear frequency response analysis of large space truss structures', Nonlinear Dynamics 112, pp. 10127–10145. https://doi.org/10.1007/s11071-024-09572-1

Marín Múgica, A. and Rancho Bueno, M. (2024) 'Prediction of vibrational parameters of a machine fixture by finite element method (Dissertation)', Retrieved from https://urn.kb.se/resolve?urn=urn:nbn:se:his:diva-24277

Mathis, A.T. Balaji, N.N. Kuether, R.J. Brink, A.R. Brake, M.R. and Quinn, D.D. (2020) 'A review of damping models for structures with mechanical joints', Applied Mechanics Reviews, 72(4), 040802.

Morsy, A. A. Xu, Z. Tiso, P. and Haller, G. (2024) 'Reducing Finite Element Models of Bolted Joints Using Spectral Submanifolds', Available at SSRN4980389. https://ssrn.com/abstract=4980389.

Paehr, M. and Panning-von Scheidt, L. (2025) 'Application of Interface Reduction Methods to Rotordynamic Casing Models', ASME. J. Eng. Gas Turbines Power. 147(5): 051019. https://doi.org/10.1115/1.4066606

Pandey, P. et al. (2025) 'Modelling and stochastic updating of nonlinear structural joints. Mechanical Systems and Signal Processing', 232: 112697.‏ ISSN 0888-3270. https://doi.org/10.1016/j.ymssp.2025.112697

Petrov, E.P. and D. J. Ewins, D.J. (2003) 'Analytical formulation of friction interface elements for analysis of nonlinear multi-harmonic vibrations of bladed disks', J, turbomach., 125(2), pp. 364-371.

Riks, E. (1979) 'An incremental approach to the solution of snapping and buckling problems and international journal of solids and structures', 15(7), pp. 529-551.

Sanliturk, K. Y. Imregun, M., and Ewins, D. J. (1997) 'Harmonic Balance Vibration Analysis of Turbine Blades with Friction Dampers', ASME. J. Vib. Acoust. 119(1), pp. 96–103. https://doi.org/10.1115/1.2889693

Segalman, D. J. (2005) 'A Four-Parameter Iwan Model for Lap-Type Joints', ASME. J. Appl. Mech. September, 72(5), pp. 752–760. https://doi.org/10.1115/1.1989354

Segalman, D. J. (2007). 'Model Reduction of Systems with Localized Nonlinearities', ASME. J. Comput. Nonlinear Dynam. 2(3), pp. 249–266. https://doi.org/10.1115/1.2727495

Talik, S. et al. (2024) 'Nonlinear vibrations of a ballistic vehicle with friction joints subjected to vibroacoustic excitation-experiments, modeling and simulations', Journal of Sound and Vibration, 588: 118526.‏

Tüfekci, M. (2024) 'Development and Application of a High-Fidelity Numerical Tool for Dynamic Analysis of Bladed Disc Systems with Under platform Dampers in Aircraft Engine Turbines', Proceedings of the ASME Turbo Expo 2024: Turbomachinery Technical Conference and Exposition. Volume 10B: Structures and Dynamics — Fatigue, Fracture, and Life Prediction; Probabilistic Methods; Rotordynamics; Structural Mechanics and Vibration. London, United Kingdom. June pp. 24–28, V10BT27A008. ASME. https://doi.org/10.1115/GT2024-123318

Valanis, K.C. (1971) 'A theory of viscoplasticity without a yield surface', Arch. Mech, stos., 23(4), pp. 515-553.

Wentzel, H. (2006) 'Modelling of frictional joints in dynamically loaded structures: a review', KTH Solid Mechanics, Royal Institute of technology.

Wriggers, P. (2006) 'Computational contact mechanics', Vol. 2, p. 25, t. A. Laursen (Ed.). Berlin: Springer.

Yan, Y. Laskar, A. Cheng, Z. Menq, F. Tang, Y. Mo, Y.L. and Z. Shi, Z. (2014) 'Seismic isolation of two-dimensional periodic foundations', Journal of Applied Physics, 116(4).

Yang, D. Lu, Z.R. Liu, J. et al. (2025) 'Harmonic balance method integrated with a customized state-space algorithm for the periodic solutions of structures with frictional hysteresis', Nonlinear Dynamics, pp. 1-18. https://doi.org/10.1007/s11071-025-11352-4

Yang, Z. (2025) 'Application of Finite Element Analysis for Fracture and Damage Mechanics', cRC Press.

Yuan, J. El-Haddad, F. Salles, L. and Wong, C. (2019) 'Numerical assessment of reduced order modelling techniques for dynamic analysis of jointed structures with contact nonlinearities', Journal of Engineering for Gas Turbines and Power, 141(3), 031027.

Yuan, K. Zhu, Z. Chen, W. and Zhu, W. (2024) 'Development and Validation of a New Type of Displacement-Based Miniatured Laser Vibrometers', sensors, 24(16), pp. 5230.

Yuan, Y. Zhang, W. and Wang, J. (2025) 'Vibration power flow of nonlinear periodic dynamic response in helical gears based on harmonic balance method', Nonlinear Dynamics, pp. 1-30. https://doi.org/10.1007/s11071-025-11363-1

Zhang, C. Hu, D. and Yang, T. (2024) 'Research of artificial intelligence operations for wind turbines considering anomaly detection', root cause analysis, and incremental training, reliability Engineering & System Safety, 241, 109634.

Downloads

Published

2026-11-14

How to Cite

Alsayyad, Taha Hussein Karam. “MODELING AND SIMULATION OF NONLINEAR JOINT BEHAVIOR IN INDUSTRIAL ASSEMBLIES USING HARMONIC BALANCE METHOD AND FINITE ELEMENT ANALYSIS”. Kufa Journal of Engineering, vol. 17, no. 4, Nov. 2026, pp. 157-80, https://doi.org/10.30572/2018/KJE/1704010.

Share