HIGH-EFFICIENCY TRIPLE-INPUT DC–DC CONVERTER WITH OPTIMIZED DESIGN FOR RENEWABLE POWER SYSTEMS
DOI:
https://doi.org/10.30572/2018/KJE/170417Keywords:
DC–DC Converter, High Step-Up Converter, Multi-Input Topology, Switched-Capacitor, Renewable Energy Integration, Voltage Gain, Efficiency Optimization, Loss Analysis, Electric Vehicle Power SystemsAbstract
Small renewable sources such as photovoltaic strings, fuel cells and batteries rarely share a common voltage, and none of these sources comes close to the 120 V bus expected by many auxiliary loads. A triple-input high step-up direct current to direct current (DC–DC) converter is reported here for exactly that situation. The circuit uses one switched-capacitor branch and three inductor–switch cells fed from 12 V, 24 V and 18 V, and was sized for 120 V at 2 A into a 60 Ω load, roughly the rating of an electric vehicle auxiliary rail. Duty ratios of 0.90, 0.80 and 0.85 set the three gains at 10, 5 and about 6.7. Each inductor (0.27 mH, 0.48 mH and 0.3825 mH) was chosen for the same 0.4 A current ripple, and a 22 µF capacitor holds the output ripple under 1 V at 100 kHz. Losses were estimated term by term: conduction and switching in every metal–oxide–semiconductor field-effect transistor (MOSFET), forward drop and reverse recovery in the diodes, copper and core loss in the inductors, equivalent series resistance (ESR) loss in the capacitor, and gate-drive power. The simulated total loss was 3.5 W with V1 alone and 5.75 W with all three inputs, i.e. 98.56% and 97.66% efficiency at 240 W, and the change of output voltage between no load and full load was 1.67%. In the triple-input case, 3.4 W of the 5.75 W was lost in the MOSFETs and diodes, so the switching devices, and not the inductors or the capacitor, limit further improvement. The converter is aimed at renewable source integration, electric vehicle auxiliary supplies and small distributed generation units
Downloads
References
Al-Sakini, D.S. (2025). Preventive treatment for power transformer by analysis of dissolved gas and using fuzzy logic. Kufa Journal of Engineering, 16(3), pp. 353–367.
Balapanuru, O., Lokhande, M. M., & Aware, M. V. (2023). Performance Improvement by Sampling Position Approach in Dual Loop Digital ACM Controlled DC-DC Boost Converter. IEEE Transactions on Circuits and Systems II: Express Briefs, 70(4), 1565–1569.
Biswas, K., & Ray, O. (2022). Calibration Method of Equivalent Series Resistance Parameter for Nonintrusive Current Sensors Used in DC–DC Power Electronic Converters. IEEE Sensors Letters, 6(9), 1–4.
Cheepati, K. R., Parimalasundar, E., Suresh, K., Reddy, C. R., Alqahtani, M. M., & Khalid, M. (2023). Design of Triple Tuned Passive Harmonic Power Filter—A Novel Approach. Canadian Journal of Electrical and Computer Engineering, 46(4), 270–277.
Dabbagh, Z. and Jeaeb, S.W.S. (2025). Full soft-switching high step-up cascaded boost converter with three-winding coupled-inductor. Kufa Journal of Engineering, 16(3), pp. 271–291.
Errouissi, R., Shareef, H., Viswambharan, A., & Wahyudie, A. (2022). Disturbance-Observer-Based Feedback Linearization Control for Stabilization and Accurate Voltage Tracking of a DC–DC Boost Converter. IEEE Transactions on Industry Applications, 58(5), 6687–6700.
Gaied, H., Flah, A., Kraiem, H., & Prokop, L. (2024). A Comparison Between the Quality of Two Level and Three Levels Bidirectional Buck-Boost Converter Using the Neural Network Controller. IEEE Access, 12, 94323–94336.
Gholizadeh, H., Dehghan, M., Shahrivar, R. S., Samimi, M. H., & Ghassemi, M. (2024). A Non-Isolated Quadratic DC–DC Converter Improved by Voltage-Lift Technique Suitable for High-Voltage Applications. IEEE Access, 12, 158292–158310.
Goyal, V. K., & Shukla, A. (2022). Two-Stage Hybrid Isolated DC–DC Boost Converter for High Power and Wide Input Voltage Range Applications. IEEE Transactions on Industrial Electronics, 69(7), 6751–6763.
Hadi, A.-R.S., Alamili, A. and Kadhum, A.A. (2025). Robust sliding-mode-based learning for maximum power point tracking photovoltaics system. Kufa Journal of Engineering, 16(2), pp. 249–262.
Israyelu, M., & Sashidhar, S. (2024). State-Space Modeling and Validation of Circuit Parasitics' Effect on the Performance of a High-Gain Nonisolated Switched Inductor Topology. IEEE Journal of Emerging and Selected Topics in Industrial Electronics, 5(4), 1654–1665.
Khan, M. S., Nag, S. S., Das, A., & Yoon, C. (2023). Analysis and Control of an Input-Parallel Output-Series Connected Buck-Boost DC–DC Converter for Electric Vehicle Powertrains. IEEE Transactions on Transportation Electrification, 9(2), 2015–2025.
Lin, C.-H., Khan, M. S., Ahmad, J., Liu, H.-D., & Hsiao, T.-C. (2024). Design and Analysis of Novel High-Gain Boost Converter for Renewable Energy Systems (RES). IEEE Access, 12, 24262–24273.
Liu, H.-D., Jana, A. S., & Lin, C.-H. (2024). An Improved High Gain Continuous Input Current Quadratic Boost Converter for Next–Generation Sustainable Energy Application. IEEE Transactions on Circuits and Systems II: Express Briefs, 71(5), 2839–2843.
Mandal, S., Prabhakaran, P., Dominic, D. A., & Parameswaran, A. P. (2025). A Transformerless Bidirectional Active Switched Inductor-Based SEPIC High-Gain DC–DC Converter with Buck–Boost Capability. IEEE Access, 13, 137139–137154.
Moisello, E., Fusetto, S., Malcovati, P., & Bonizzoni, E. (2024). A Generalized Active Voltage Balancing Circuit Implementation for Flying Capacitor 3-Level Switching-Mode DC–DC Converters. IEEE Open Journal of Circuits and Systems, 5, 365–376.
Naik, M. D., Vinatha, U., Naik, M. V., & Bonthagorla, P. K. (2025). Investigation and Performance Evaluation of Novel Single-Switch High-Gain DC-DC Converters for DC Microgrid Applications. IEEE Access, 13, 103798–103808.
Nikbakht, M., Abbaszadeh, K., Abbasian, S., Allahyari, H., & Gorji, S. A. (2023). An Ultra-Step-Up Quadratic Boost DC–DC Converter Based on Coupled Inductors and Quasi-Resonance Operation. IEEE Journal of Emerging and Selected Topics in Industrial Electronics, 4(4), 1096–1109.
Parimalasundar, E., Senthilkumar, R., Jayanthi, R., Dharmaprakash, N., Rajavinu, I.A.D. and Adaikalam, I.A.D. (2025). Advanced 15-level inverter design for solar PV integration. Kufa Journal of Engineering, 16(3), pp. 161–175.
Park, J., Maeng, J., Jeon, J., Kim, H., & Kim, C. (2022). A Four-Phase Hybrid Step-Up/Down Converter with RMS Inductor Current Reduction and Delay-Based Zero-Current Detection. IEEE Transactions on Power Electronics, 37(4), 3708–3712.
Rajesh, R., Prabaharan, N., & Santhosh, T. K. (2023). Design and Analysis of a Non-Isolated DC-DC Converter with a High-Voltage Conversion Ratio. IEEE Transactions on Circuits and Systems II: Express Briefs, 70(6), 2036–2041.
Rao, B. T., & De, D. (2022). Effective Leakage Energy Recycling in High Gain DC-DC Converter with Coupled Inductor. IEEE Transactions on Circuits and Systems II: Express Briefs, 69(7), 3284–3288.
Singh, R., Suresh, K., Parimalasundar, E., Kumar, B. H., Bajaj, M., & Tuka, M. B. (2024a). Design and Performance Evaluation of a Multi-Load and Multi-Source DC-DC Converter for Efficient Electric Vehicle Power Systems. Scientific Reports, 14(1), Article 77349.
Singh, R., Suresh, K., Parimalasundar, E., Kumar, B. H., Bajaj, M., & Tuka, M. B. (2024b). A High-Efficiency Poly-Input Boost DC–DC Converter for Energy Storage and Electric Vehicle Applications. Scientific Reports, 14(1), Article 69254.
Downloads
Published
Issue
Section
License
Copyright (c) 2026 M. Lokanadham , E. Parimalasundar

This work is licensed under a Creative Commons Attribution 4.0 International License.












