INFLUENCE OF ZIRCONIUM ON MECHANICAL AND WEAR PROPERTIES OF MONEL400 BY DOUBLE-WIRE ARC ADDITIVE MANUFACTURING

Authors

  • Haneen H. Hlail Department of Metallurgical Engineering, College of Materials Engineering, University of Babylon, Iraq
  • Basem Al-Zubaidy Department of Metallurgical Engineering, College of Materials Engineering, University of Babylon, Iraq
  • Zuheir Talib Khulief Department of Metallurgical Engineering, College of Materials Engineering, University of Babylon, Iraq

DOI:

https://doi.org/10.30572/2018/KJE/170427

Keywords:

Monel 400, Double Wire Arc Additive Manufacturing (DWAAM), zirconium addition, wear behavior

Abstract

Additive manufacturing (AM) using Multi Wire Arc Additive Manufacturing (MWAAM) enables the production of high-performance nickel-based alloys with tailored properties. This study examines how zirconium (Zr) affects the microstructure and mechanical behavior of Monel 400 alloy. Three compositions (Monel 400, Monel 400 + 0.5 wt.% Zr, and Monel 400 + 1 wt.% Zr) were deposited layer-by-layer via wire arc. scanning electron microscopy (SEM)and Optical microscopy (OM) analyzed grain morphology and phase distribution, while Vickers micro-hardness testing (HV0.2) assessed local mechanical variations in different wall regions. Tensile tests in vertical and horizontal orientations evaluated the overall mechanical response. Results show Zr addition significantly impacts microstructure and properties the 1 wt.% Zr alloy had the most refined grains, higher hardness reaching approximately of 160 HV0.2 at top,165 HV0.2, and 140-145 at bottom, and tensile value in the horizontal orientation (H), exhibits the highest UTS (310) and YS (440). The 0.5 wt.% Zr alloy showed partial grain refinement and localized hardness peaks reaching a maximum of ~180 HV0.2 at top,145-150 HV0.2 at middle and 137 HV0.2 at bottom, while Monel 400 had coarse grains and lower performance. These results show the enhance Monel400 in   additive manufacturing, indicating controlled Zr addition can improve microstructure and tensile properties for durable components in demanding environments

Downloads

Download data is not yet available.

References

Kostryzhev, A. G., Marenych, O. O., Pan, Z., Li, H., & Van Duin, S. (2023). Strengthening mechanisms in Monel K500 alloyed with Al and Ti. Journal of Materials Science, 58(9), 4150-4164.‏

Chen, L., He, Y., Yang, Y., Niu, S., & Ren, H. (2017). The research status and development trend of additive manufacturing technology. The International Journal of Advanced Manufacturing Technology, 89, 3651-3660.

Marenych, O., & Kostryzhev, A. (2020). Strengthening mechanisms in nickel-copper alloys: A review. Metals, 10(10), 1358.‏

Zhu, Y., Wang, J., Liu, H., & Yan, F. (2022). The tribo-corrosion behavior of monel 400 Alloy in marine environment at varied rotational velocities. Metals, 12(9), 1503.‏

Kukliński, M., Bartkowska, A., Przestacki, D., & Kinal, G. (2020). Influence of microstructure and chemical composition on microhardness and wear properties of laser borided Monel 400. Materials, 13(24), 5757

Chintakindi, S., Alsamhan, A., Abidi, M. H., & Kumar, M. P. (2022). Annealing of Monel 400 alloy using principal component analysis, hyper-parameter optimization, machine learning techniques, and multi-objective particle swarm optimization. International Journal of Computational Intelligence Systems, 15(1), 18

Zhu, Y., Liu, H., Zhang, D., Wang, J., & Yan, F. (2022). Effect of polarization potentials on tribocorrosion behavior of Monel 400 alloy in seawater environment. Tribology International, 168, 107445.‏

Zhu, Y., Liu, H., Wang, J., & Yan, F. (2022). Antagonistic effect of electrochemical corrosion on the mechanical wear of Monel 400 alloy in seawater. Corrosion Science, 198, 110120.‏

Lippold, J. C., Kiser, S. D., & DuPont, J. N. (2011). Welding metallurgy and weldability of nickel-base alloys. John Wiley & Son

Abdo, B. M., Almuzaiqer, R., Noman, M. A., & Chintakindi, S. (2023). Investigation of Heat Annealing and Parametric Optimization for Drilling of Monel-400 Alloy. Journal of Manufacturing and Materials Processing, 7(5), 170.‏

Kang, B., Lee, Y., Kim, J., Ha, T., & Kim, Y. (2024). Microstructural analysis on grain boundary of boron–and zirconium–Containing wrought nickel-based superalloys. Crystals, 14(3), 290.‏

Martínez, C., Aguilar, C., Briones, F., Guzmán, D., Zelaya, E., Troncoso, L., & Rojas, P. A. (2018). Effects of Zr on the amorphization of Cu-Ni-Zr alloys prepared by mechanical alloying. Journal of alloys and compounds, 765, 771-781.‏

Hossain, I., Sakib Khan, M., Khan, I. K., Hossain, K. R., He, Y., & Wang, X. (2024). TECHNOLOGY OF ADDITIVE MANUFACTURING: A COMPREHENSIVE REVIEW. Kufa Journal of Engineering, 15(1).‏

Jie, Z., Zhang, J., Huang, T., Su, H., Zhang, Y., Liu, L., & Fu, H. (2016). Effects of boron and zirconium additions on the fluidity, microstructure and mechanical properties of IN718C superalloy. Journal of Materials Research, 31(22), 3557-3566.‏

Tsai, Y. L., Wang, S. F., Bor, H. Y., & Hsu, Y. F. (2014). Effects of Zr addition on the microstructure and mechanical behavior of a fine-grained nickel-based superalloy at elevated temperatures. Materials Science and Engineering: A, 607, 294-301.‏

Hosseini, S. A., Abbasi, S. M., Madar, K. Z., & Yazdi, H. M. K. (2018). The effect of boron and zirconium on wrought structure and γ-γ′ lattice misfit characterization in nickel-based superalloy ATI 718Plus. Materials Chemistry and Physics, 211, 302-311.‏

Martínez, C., Briones, F., Rojas, P., Ordoñez, S., Aguilar, C., & Guzmán, D. (2017). Microstructure and mechanical properties of copper, nickel and ternary alloys Cu-Ni-Zr obtained by mechanical alloying and hot pressing. MRS Advances, 2(50), 2831-2836.‏

Yang, H., Kong, Z., & Sarder, M. D. (2016). Additive manufacturing: a new paradigm for manufacturing. In Proceedings of the 2016 Industrial and Systems Engineering Research Conference, Availability, Development (Vol. 14, p. 102).‏

Guo, Y., Quan, G., Celikin, M., Ren, L., Zhan, Y., Fan, L., & Pan, H. (2022). Effect of heat treatment on the microstructure and mechanical properties of AZ80M magnesium alloy fabricated by wire arc additive manufacturing. Journal of magnesium and alloys, 10(7), 1930-1940.‏

Prado-Cerqueira, J. L., Diéguez, J. L., & Camacho, A. M. (2017). Preliminary development of a wire and arc additive manufacturing system (WAAM). Procedia Manufacturing, 13, 895-902

McAndrew, A. R., Rosales, M. A., Colegrove, P. A., Hönnige, J. R., Ho, A., Fayolle, R., ... & Pinter, Z. (2018). Interpass rolling of Ti-6Al-4V wire arc additively manufactured features for microstructural refinement. Additive Manufacturing, 21, 340-349.‏

Williams, S. W., Martina, F., Addison, A. C., Ding, J., Pardal, G., & Colegrove, P. (2016). Wire+ arc additive manufacturing. Materials science and technology, 32(7), 641-647.‏

Suárez, A., Veiga, F., Bhujangrao, T., & Aldalur, E. (2022). Study of the mechanical behavior of topologically optimized arc-wire direct energy deposition aerospace fixtures. Journal of Materials Engineering and Performance, 31(8), 6270-6282.‏

Ali, R., & Al-Zubaidy, B. (2023). A Review of Preparation and Characterization of Additively Manufactured Stainless Steel. Journal of University of Babylon for Engineering Sciences, 31(6), 31-49

Qi, Z., Cong, B., Qi, B., Sun, H., Zhao, G., & Ding, J. (2018). Microstructure and mechanical properties of double-wire+ arc additively manufactured Al-Cu-Mg alloys. Journal of Materials Processing Technology, 255, 347-353.‏

Li, Z., Cui, Y., Yu, Z., & Liu, C. (2021). In-situ fabrication of Ti2AlNb-based alloy through double-wire arc additive manufacturing. Journal of Alloys and Compounds, 876, 160021

M. Adinarayanappa, S., & Simhambhatla, S. (2017). Twin-wire welding-based additive manufacturing (TWAM): manufacture of functionally gradient objects. Rapid Prototyping Journal, 23(5), 858-868.

Lu, Y., Chen, S., Shi, Y., Li, X., Chen, J., Kvidahl, L., & Zhang, Y. M. (2014). Double-electrode arc welding process: principle, variants, control and developments. Journal of Manufacturing Processes, 16(1), 93-108.‏

Wu, W., Xue, J., Zhang, Z., Ren, X., & Xie, B. (2019). Process optimization on multilayer morphology during the 316L double-wire CMT+ P deposition process. Metals, 9(12), 1334.‏

Zhang, Y. M., Jiang, M., & Lu, W. (2004). Double electrodes improve GMAW heat input control. Welding Journal, 83(11), 39-41

Wu, W., Xue, J., & Yao, P. (2020). A comparative study on single-and double-arc deposition processes. Materials and Manufacturing Processes, 35(3), 346-353.‏

Zhao, X., Chen, X., Ma, T., Zhang, P., Li, J., & Zhang, X. (2024). Microstructure and properties of a shape memory alloy Ti–Ni–Al–V fabricated by double-wire arc additive manufacturing. Heliyon, 10(2).‏

Marenych, O. O., Kostryzhev, A. G., Pan, Z., Li, H., & Van Duin, S. (2019). Comparative effect of Mn/Ti solute atoms and TiC/Ni3 (Al, Ti) nano-particles on work hardening behaviour in NiCu alloys fabricated by wire arc additive manufacturing. Materials Science and Engineering: A, 753, 262-275.‏

Downloads

Published

2026-11-14

How to Cite

Hlail, Haneen H., et al. “INFLUENCE OF ZIRCONIUM ON MECHANICAL AND WEAR PROPERTIES OF MONEL400 BY DOUBLE-WIRE ARC ADDITIVE MANUFACTURING”. Kufa Journal of Engineering, vol. 17, no. 4, Nov. 2026, pp. 497-10, https://doi.org/10.30572/2018/KJE/170427.

Share