MIXED CONVECTION HEAT TRANSFER IN VENTILATEDCAVITIES FILLED WITH CU/ WATER AND CUO/ WATERNANOFLUIDS

Authors

  • Fares Khalfallah Department of Physics, Faculty of Sciences, University of M’sila, M’sila, Algeria
  • Razik Benderradji Department of Physics, Faculty of Sciences, University of M’sila, M’sila, Algeria
  • Hamza Gouidmi Department of Mechanical Engineering, Faculty of Sciences and Technology, University of Bordj Bou Arreridj, Bordj Bou Arreridj, Algeria

DOI:

https://doi.org/10.30572/2018/KJE/170424

Keywords:

Mixed convection, Ventilated cavity, Nanofluid, Copper, Copper oxide, Nusselt number

Abstract

Laminar mixed convection was computed in a square cavity with two openings, one tenth of the side high, at the foot of the vertical walls. Cold fluid entered on the left, and the right wall above the outlet was held at a higher uniform temperature. The fluid was water or a single-phase Cu or CuO suspension at 2, 6, and 10% by volume, with Brinkman viscosity and Maxwell conductivity. Finite-volume solutions covered  to 500 at , and  to  at . At , the average Nusselt number of the heated wall rose from 4.77 to 15.94 between  and 500. At 10% by volume, Cu raised it by 9.8 to 13.6% and CuO by 3.7 to 5.2%. Between 68 and 73% of the wall heat flow entered through the lowest third of the heated wall. At , the average Nusselt number peaked at . It fell by 22 to 24% at , where warm fluid stratified in the upper half of the cavity. The particle gain was largest at , 13.3% for Cu, where the Cu suspension kept a recirculating upper cell that water had lost. Under the property models, both particles raise the effective conductivity almost equally, so the advantage of Cu follows mainly from its higher density. The coolant left at 4 to 14% of the inlet-to-wall temperature difference, and at  the upper cell recirculated 5.4 times the wall heat. The heat transfer predictions have not been validated against a benchmark with the same heating

Downloads

Download data is not yet available.

References

Al-Akam, A., Alketab, N. U. T., Hamzah, H. K., Ali, F. H., Al-Amir, Q. R., & Alahmer, A. (2025). Synergistic effects of hybrid nanofluids and dual porous layers on mixed convection in ventilated cavities. Journal of Thermal Analysis and Calorimetry, 150(26), 22029–22065. https://doi.org/10.1007/s10973-025-14993-0

Al-Mayahi, H. A. (2018). Numerical study of mixed convection flow in a lid-driven cavity. Kufa Journal of Engineering, 9(3), 128–144. https://doi.org/10.30572/2018/KJE/090310

Angirasa, D. (2000). Mixed convection in a vented enclosure with an isothermal vertical surface. Fluid Dynamics Research, 26(4), 219–233. https://doi.org/10.1016/S0169-5983(99)00024-6

Arefmanesh, A., & Mahmoodi, M. (2011). Effects of uncertainties of viscosity models for Al_2O_3–water nanofluid on mixed convection numerical simulations. International Journal of Thermal Sciences, 50(9), 1706–1719. https://doi.org/10.1016/j.ijthermalsci.2011.04.007

Arquis, E., Rady, M. A., & Nada, S. A. (2007). A numerical investigation and parametric study of cooling an array of multiple protruding heat sources by a laminar slot air jet. International Journal of Heat and Fluid Flow, 28(4), 787–805. https://doi.org/10.1016/j.ijheatfluidflow.2006.09.004

Awan, A. U., Ahammad, N. A., Ali, B., Tag-ElDin, E. M., Guedri, K., & Gamaoun, F. (2022). Significance of thermal phenomena and mechanisms of heat transfer through the dynamics of second-grade micropolar nanofluids. Sustainability, 14(15), 9361. https://doi.org/10.3390/su14159361

Behzadi, T., Shirvan, K. M., Mirzakhanlari, S., & Sheikhrobat, A. A. (2015). Numerical simulation on effect of porous medium on mixed convection heat transfer in a ventilated square cavity. Procedia Engineering, 127, 221–228. https://doi.org/10.1016/j.proeng.2015.11.333

Benzema, M., Benkahla, Y. K., Labsi, N., Ouyahia, S.-E., & El Ganaoui, M. (2019). Second law analysis of MHD mixed convection heat transfer in a vented irregular cavity filled with Ag–MgO/water hybrid nanofluid. Journal of Thermal Analysis and Calorimetry, 137(3), 1113–1132. https://doi.org/10.1007/s10973-019-08017-x

Brahimi, M., Benderradji, R., & Gouidmi, H. (2024). Mixed convection of an Ag/water nanofluid in a ventilated square cavity containing cold blocks of different shapes. WSEAS Transactions on Heat and Mass Transfer, 19, 33–40. https://doi.org/10.37394/232012.2024.19.4

Brinkman, H. C. (1952). The viscosity of concentrated suspensions and solutions. The Journal of Chemical Physics, 20(4), 571. https://doi.org/10.1063/1.1700493

Celik, I. B., Ghia, U., Roache, P. J., Freitas, C. J., Coleman, H., & Raad, P. E. (2008). Procedure for estimation and reporting of uncertainty due to discretization in CFD applications. Journal of Fluids Engineering, 130(7), 078001. https://doi.org/10.1115/1.2960953

Dawar, A., Wakif, A., Thumma, T., & Shah, N. A. (2022). Towards a new MHD non-homogeneous convective nanofluid flow model for simulating a rotating inclined thin layer of sodium alginate-based iron oxide exposed to incident solar energy. International Communications in Heat and Mass Transfer, 130, 105800. https://doi.org/10.1016/j.icheatmasstransfer.2021.105800

Dhahad, H. A., Al-Sumaily, G. F., Alawee, W. H., & Thompson, M. C. (2020). Aiding and opposing re-circulating mixed convection flows in a square vented enclosure. Thermal Science and Engineering Progress, 19, 100577. https://doi.org/10.1016/j.tsep.2020.100577

Fadel Abed, A. (2014). Numerical modeling of mixed convection heat transfer of laminar fluid in rectangular enclosure with openings in the side. Kufa Journal of Engineering, 4(1), 21–38. https://doi.org/10.30572/2018/KJE/411250

Ferziger, J. H., Perić, M., & Street, R. L. (2020). Computational methods for fluid dynamics (4th edn). Springer. https://doi.org/10.1007/978-3-319-99693-6

Hasan, M., Priam, S. S., Nur-E Faiaz, A., Azad, A. K., & Rahman, M. M. (2023). Influence of thermal conductivity on transient mixed convection in a vented cavity with a hollow cylinder and filled with CNT–water nanofluid. Heliyon, 9(3), e13850. https://doi.org/10.1016/j.heliyon.2023.e13850

Hinojosa, J. F., Rodríguez, N. A., & Xamán, J. (2016). Heat transfer and airflow study of turbulent mixed convection in a ventilated cavity. Journal of Building Physics, 40(3), 204–234. https://doi.org/10.1177/1744259115611640

Jasim, L. M., Hamzah, H., Canpolat, C., & Sahin, B. (2021). Mixed convection flow of hybrid nanofluid through a vented enclosure with an inner rotating cylinder. International Communications in Heat and Mass Transfer, 121, 105086. https://doi.org/10.1016/j.icheatmasstransfer.2020.105086

Jung, J.-Y., Oh, H.-S., & Kwak, H.-Y. (2006). Forced convective heat transfer of nanofluids in microchannels. Proceedings of the ASME International Mechanical Engineering Congress and Exposition, Volume 3: Heat Transfer. https://doi.org/10.1115/IMECE2006-13851

Kamel, M. S., Albdoor, A. K., & Nghaimesh, S. J. (2025). Simulation of heat transfer and a new nanofluid flow inside a horizontal channel. Kufa Journal of Engineering, 16(3), 658–674. https://doi.org/10.30572/2018/KJE/160337

Khanafer, K., Vafai, K., & Lightstone, M. (2003). Buoyancy-driven heat transfer enhancement in a two-dimensional enclosure utilizing nanofluids. International Journal of Heat and Mass Transfer, 46(19), 3639–3653. https://doi.org/10.1016/S0017-9310(03)00156-X

Li, H., Zhang, S., Ji, Y., Sun, M., Li, X., & Sheng, Y. (2022). The influence of catchment scale on comprehensive heat transfer performance about tube fin heat exchanger in numerical calculation. Energy Reports, 8, 147–155. https://doi.org/10.1016/j.egyr.2021.11.045

Lotfi, R., Saboohi, Y., & Rashidi, A. M. (2010). Numerical study of forced convective heat transfer of nanofluids: Comparison of different approaches. International Communications in Heat and Mass Transfer, 37(1), 74–78. https://doi.org/10.1016/j.icheatmasstransfer.2009.07.013

Mahmoudi, A. H., Shahi, M., & Talebi, F. (2010). Effect of inlet and outlet location on the mixed convective cooling inside the ventilated cavity subjected to an external nanofluid. International Communications in Heat and Mass Transfer, 37(8), 1158–1173. https://doi.org/10.1016/j.icheatmasstransfer.2010.04.004

Maxwell, J. C. (1881). A treatise on electricity and magnetism (2nd edn, Vol. 1). Clarendon Press.

Mehrizi, A. A., Farhadi, M., Afroozi, H. H., Sedighi, K., & Darz, A. A. R. (2012). Mixed convection heat transfer in a ventilated cavity with hot obstacle: Effect of nanofluid and outlet port location. International Communications in Heat and Mass Transfer, 39(7), 1000–1008. https://doi.org/10.1016/j.icheatmasstransfer.2012.04.002

Moumni, H., Welhezi, H., & Sediki, E. (2017). Numerical investigation of heat transfer enhancement in a square ventilated cavity with discrete heat sources using nanofluid. High Temperature, 55(3), 426–433. https://doi.org/10.1134/S0018151X17030166

Nassan, T. H., Heris, S. Z., & Noie, S. H. (2010). A comparison of experimental heat transfer characteristics for Al_2O_3/water and CuO/water nanofluids in square cross-section duct. International Communications in Heat and Mass Transfer, 37(7), 924–928. https://doi.org/10.1016/j.icheatmasstransfer.2010.04.009

Niemann, P., & Schmitz, G. (2020). Air conditioning system with enthalpy recovery for space heating and air humidification: An experimental and numerical investigation. Energy, 213, 118789. https://doi.org/10.1016/j.energy.2020.118789

Oztop, H. F., & Abu-Nada, E. (2008). Numerical study of natural convection in partially heated rectangular enclosures filled with nanofluids. International Journal of Heat and Fluid Flow, 29(5), 1326–1336. https://doi.org/10.1016/j.ijheatfluidflow.2008.04.009

Patankar, S. V. (2018). Numerical heat transfer and fluid flow. CRC Press. https://doi.org/10.1201/9781482234213

Punia, A., & Ray, R. K. (2025). Numerical investigation of three-dimensional mixed convection in a vented cavity with heated baffles. International Communications in Heat and Mass Transfer, 169, 109738. https://doi.org/10.1016/j.icheatmasstransfer.2025.109738

Raja, M. A. Z., Shoaib, M., Zubair, G., Khan, M. I., Punith Gowda, R. J., Prasannakumara, B. C., & Guedri, K. (2022). Intelligent neuro-computing for entropy generated Darcy–Forchheimer mixed convective fluid flow. Mathematics and Computers in Simulation, 201, 193–214. https://doi.org/10.1016/j.matcom.2022.05.004

Rao, G. M., & Narasimham, G. S. V. L. (2007). Laminar conjugate mixed convection in a vertical channel with heat generating components. International Journal of Heat and Mass Transfer, 50(17–18), 3561–3574. https://doi.org/10.1016/j.ijheatmasstransfer.2006.12.030

Ren, F., Du, J., Cai, Y., Xu, Z., Zhang, D., & Liu, Y. (2021). Numerical simulation study on thermal performance of sub-tropical double-layer energy storage floor combined with ceiling energy storage radiant air conditioning. Case Studies in Thermal Engineering, 28, 101696. https://doi.org/10.1016/j.csite.2021.101696

Rostamani, M., Hosseinizadeh, S. F., Gorji, M., & Khodadadi, J. M. (2010). Numerical study of turbulent forced convection flow of nanofluids in a long horizontal duct considering variable properties. International Communications in Heat and Mass Transfer, 37(10), 1426–1431. https://doi.org/10.1016/j.icheatmasstransfer.2010.08.007

Saha, S., Hasan, M. N., & Khan, I. A. (2009). Double diffusive mixed convection heat transfer inside a vented square cavity. Chemical Engineering Research Bulletin, 13(1), 17–24. https://doi.org/10.3329/cerb.v13i1.2512

Salih, S., & Yaseen, D. (2021). Numerical modeling of laminar forced convective enhancement of (Al_2O_3–water) nanofluids in a circular pipe. Kufa Journal of Engineering, 11(4), 19–30. https://doi.org/10.30572/2018/KJE/110402

Selimefendigil, F., & Oztop, H. F. (2025). Effects of combined utilization of active cooler/heater and blade-shaped nanoparticles in base fluid for performance improvement of thermoelectric generator mounted in between vented cavities. Arabian Journal for Science and Engineering, 50(4), 2925–2943. https://doi.org/10.1007/s13369-025-09972-4

Selvakumar, R. D., Zhonglin, D., & Wu, J. (2022). Heat transfer intensification by EHD conduction pumping for electronic cooling applications. International Journal of Heat and Fluid Flow, 95, 108972. https://doi.org/10.1016/j.ijheatfluidflow.2022.108972

Shahi, M., Mahmoudi, A. H., & Talebi, F. (2010). Numerical study of mixed convective cooling in a square cavity ventilated and partially heated from the below utilizing nanofluid. International Communications in Heat and Mass Transfer, 37(2), 201–213. https://doi.org/10.1016/j.icheatmasstransfer.2009.10.002

Sourtiji, E., Gorji-Bandpy, M., Ganji, D. D., & Hosseinizadeh, S. F. (2014). Numerical analysis of mixed convection heat transfer of Al_2O_3–water nanofluid in a ventilated cavity considering different positions of the outlet port. Powder Technology, 262, 71–81. https://doi.org/10.1016/j.powtec.2014.04.061

Tiwari, R. K., & Das, M. K. (2007). Heat transfer augmentation in a two-sided lid-driven differentially heated square cavity utilizing nanofluids. International Journal of Heat and Mass Transfer, 50(9–10), 2002–2018. https://doi.org/10.1016/j.ijheatmasstransfer.2006.09.034

Uğurlubilek, N., Sert, Z., Selimefendigil, F., & Öztop, H. F. (2025). Optimization of conductive partitions on the mixed convection in a vented cavity. Heat Transfer, 54(2), 1530–1542. https://doi.org/10.1002/htj.23200

Velkennedy, R., Jeseema Nisrin, J., Kalidasan, K., & Rajeshkanna, P. (2021). Numerical investigation of convective heat transfer in a rectangular vented cavity with two outlets and cold partitions. International Communications in Heat and Mass Transfer, 129, 105659. https://doi.org/10.1016/j.icheatmasstransfer.2021.105659

Versteeg, H. K., & Malalasekera, W. (2007). An introduction to computational fluid dynamics: The finite volume method (2nd edn). Pearson Education.

Downloads

Published

2026-11-14

How to Cite

Khalfallah, Fares, et al. “MIXED CONVECTION HEAT TRANSFER IN VENTILATEDCAVITIES FILLED WITH CU WATER AND CUO WATERNANOFLUIDS”. Kufa Journal of Engineering, vol. 17, no. 4, Nov. 2026, pp. 415-38, https://doi.org/10.30572/2018/KJE/170424.

Share