Effect of Walnut Shell Powder and Nano-TiO2 on the Mechanical, Thermal, and Water Absorption Properties of Polyester Composites

Raghad Hussein  Mohammed; Rana Mahdi  Salih

doi:10.30572/2018/KJE/170338

Authors

Raghad Hussein Mohammed Lecturer, Department of Medical and Industrial Materials, College of Applied Sciences, University of Technology- Iraq
Rana Mahdi Salih Professor, Applied Sciences Research Unit, College of Applied Sciences, University of Technology, Iraq

DOI:

https://doi.org/10.30572/2018/KJE/170338

Keywords:

Polymers, Composites, Walnut shell, Reinforcement, Mechanical properties, SEM, Recycling, Unsaturated polyester

Abstract

This study investigates the potential of using ground walnut shell powder as a natural reinforcement for unsaturated polyester resin for sustainability and recycling, as an alternative to synthetic reinforcements. The main objective is to assess the effect of various filler contents 5%, 15%, and 25% wt. on the thermal and mechanical performance of the prepared composites. Hand lay-up technique was used to fabricate the casts, and the designated test specimens were cut according to the dimensions in the standard specification of each test (Impact strength, flexural strength, water uptake, and thermal conductivity). The results showed a significant improvement in the impact and flexural strengths at 15% wt. reinforcement, while thermal conductivity dropped with increasing filler weight fraction, suggesting enhanced thermal insulation. Water uptake increased at the first few weeks until a steady state is reached, after which the 25%wt. specimens showed the highest rate of water absorption, followed by the 15% and 5%wt. specimens, respectively. These findings show the suitability of using locally-available and inexpensive agricultural waste as an eco-friendly reinforcement for polymeric composites

Downloads

Download data is not yet available.

References

Ahlawat V, Kajal S, Parinam A. (2019) 'Experimental analysis of tensile, flexural, and tribological properties of walnut shell powder/polyester composites', Euro-Mediterranean Journal for Environmental Integration, 4(1):1.

Al‐Arkawazi RR, Azdast T and Hasanzadeh R. (2025) 'Investigation of the effects of walnut shell wood particles on the mechanical properties of injection molded wood‐polyethylene‐polycarbonate composites', SPE Polymers, 6(2), e10175.

Al-Sarraf, M.A. (2024) 'Sustainable and environmentally friendly composites: Development of walnut shell powder-reinforced polypropylene composites for potential automotive applications', Journal of the Mechanical Behavior of Materials, 33(1), 20240017.

Al-Zubaydi AS, Salih RM and Al-Dabbagh B.M. (2021) 'Effect of nano TiO2 particles on the properties of carbon fiber-epoxy composites' Progress in Rubber, Plastics and Recycling Technology, 7(3), 216-32.

ASTM D570-22 Standard Test Method for Water Absorption of Plastics.

ASTM D790-10 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials.

Ayrilmis N, Kaymakci A and Ozdemir F. (2013) 'Physical, mechanical, and thermal properties of polypropylene composites filled with walnut shell flour', Journal of Industrial and Engineering Chemistry, 19(3), 908-14.

Bangera MK and Kotian R. (2020) 'Effect of titanium dioxide nanoparticle reinforcement on flexural strength of denture base resin: A systematic review and meta-analysis', Japanese Dental Science Review, 56(1), 68-76.

Barczewski M, Suárez L, Mietliński P, Kloziński A, Ortega Z. (2014) 'Relationship between the shape of giant reed-based fillers and thermal properties of polyethylene composites: structural related thermal expansion and diffusivity studies', Waste and Biomass Valorization, 15(12), 7033-42.

Burhan, S., Abed, M. and Salih, M.A.S.M.A. (2019) 'Rice Husk Ash as a nano-filler to synthesize thermosetting polymer nanocomposites and evaluation of its tribological behavior', Kufa Journal of Engineering, 10(1), 78-91.

Fei P, Shi Y, Zhou M, Cai J, Tang S, Xiong H. (2013) 'Effects of nano‐TiO2 on the properties and structures of starch/poly (ε‐caprolactone) composites', Journal of Applied Polymer Science, 130(6), 4129-4136.

Gbenebor, O., Osabumwenre, F. and Adeosun, S. (2020) 'Structural, Mechanical and Thermal Properties of Low Density Polyethyline/Biomass Composite: Effects of Particle Size', Kufa Journal of Engineering, 11(2), 68-84.

Gürü, M., Atar, M. and Yıldırım, R. (2008) 'Production of polymer matrix composite particleboard from walnut shell and improvement of its requirements', Materials & Design, 29(1), 284-287.

Hejna A, Sulyman M, Przybysz M, Saeb MR, Klein M and Formela K. (2020) 'On the correlation of lignocellulosic filler composition with the performance properties of poly (ε-caprolactone) based biocomposites', Waste and Biomass Valorization, 11(4), 1467-79.

Hilal RH. (2023) 'Using Taguchi experimental design to calculate and analyze thermal conductivity for (polyacrylamide-kaolin) composite', Kuwait Journal of Science 1; 50 (3A).

Hilal, R.H. and Nassif, R.A. (2025) 'Diffusion coefficient of epoxy/NBR/bentonite tri-composite in the presence of chemical solutions', Kufa Journal of Engineering, 16(3), 425-433.

ISO 179-1:2023Plastics - Determination of Charpy impact properties.

Iyer T, Nayak SY, Hiremath A, Heckadka SS and Jaideep JP. (2023) 'Influence of TiO2 nanoparticle modification on the mechanical properties of basalt-reinforced epoxy composites', Cogent Engineering, 10(1), 2227397.

Khantwal R, Gupta G, Negi RS. (2016) 'Walnut shell reinforced composite: a review', International Journal of Scientific and Engineering Research, 7(5), 179-89.

Kumar K, Ghosh PK, Kumar A. (2016) 'Improving mechanical and thermal properties of TiO2-epoxy nanocomposite', Composites Part B: Engineering, 97, 353-60.

Lee, S., Ahn, K., Hong, S.J. and Kim, Y.T. (2025) 'Effect of Sequence-Based Incorporation of Fillers, Kenaf Fiber and Graphene Nanoplate, on Polypropylene Composites via a Physicochemical Compounding Method', Polymers, 17(14), 1955.

Li, L., Liu, S., Du, G., Jiang, S., Yang, J., Zhang, J. and Li, T. (2024) 'Sustainable engineering polymer composites fabricated using delignified bamboo fiber as reinforcement and walnut shell powder as filler', Composites Part B: Engineering, 287, 111857.

McNeill DC, Pal AK, Nath D, Rodriguez-Uribe A, Mohanty AK, Pilla S, Gregori S, Dick P and Misra M. (2024) 'Upcycling of ligno-cellulosic nutshells waste biomass in biodegradable plastic-based biocomposites uses-a comprehensive review', Composites Part C: Open Access, 1(14), 100478.

Onwubu, S.C., Naidoo, D., Obiechefu, Z. and Mokhothu, T.H. (2025) 'Biobased Filler Materials in Polymeric Composites: A Comprehensive Review of Epoxy and Polyurethane Systems'. Pre-prints.org.

Pączkowski P. 'Properties of eco-friendly composites based on post-consumer recycled resin filled with walnut shell powder', Polymers. (2023) Nov 12; 15(22):4389.

Pradhan P and Satapathy A. (2021) 'Investigation on sliding wear behaviour of walnut shell powder (WSP) filled polyester composites using finite element method', Materials Today: Proceedings, 1(44), 4190-5.

Pradhan P and Satapathy A (2022) 'Physico-mechanical characterization and thermal property evaluation of polyester composites filled with walnut shell powder', Polymers and Polymer Composites', 14(30), 09673911221077808.

Pradhan P, Nanda BP and Satapathy A. (2020) 'Polyester composites filled with walnut shell powder: Preparation and thermal characterization', Polymer Composites, 41(8), 3294-308.

Rathnam V, Kichu A, Dutta N, Maji TK and Devi N. (2022) 'Influence of organically modified nanoclay and TiO2 nanopowder on the properties of Azadirachta indica wood flour-reinforced high-density polyethylene, low-density polyethylene, polypropylene, and polyvinyl chloride nanocomposite', Journal of Thermoplastic Composite Materials, 35(10), 1468-87.

Salasinska K, Barczewski M, Górny R and Kloziński A. (2018) 'Evaluation of highly filled epoxy composites modified with walnut shell waste filler', Polymer Bulletin, 75(6), 2511-28.

Salih RM (2019) 'Preparation and characterization of human hair-reinforced epoxy', Materials Research Express, 6(8), 085332.

Salih RM. (2021) 'Study of heat and sound insulation for polymeric composites reinforced with nano clay', Polymers and Polymer Composites, 29(9): S1216-1226.

Salih RM, Al-Zubaydi AS and Deyaa BM (2025) 'Preparation and characterization of polymer blends reinforced with nano TiO2' Physica Scripta, 100(7), 075906.

Xu Z, Shen X, Wang T, Yang Y, Yi J, Cao M, Shen J, Xiao Y, Guan J, Jiang X and Tang B. (2021) 'Investigation on tribological and thermo-mechanical properties of Ti3C2 nanosheets/epoxy nanocomposites', ACS omega, 6(43), 29184-91.